Trail Gear Advisor

Photos from current listings. Actual item, color, and included accessories may vary.

Bear Gen 6 Buying Guide

Bear Gen 6 trucks are reverse-kingpin longboard trucks from Bear Trucks, engineered for strength and precise steering. The key trade-off is between the 40° baseplate for stability and the 50° baseplate for agility, plus hanger width choices that must match deck width. Buyers should prioritize forged versus cast construction and correct bushing durometer for their weight and discipline.

Truck Type:Reverse kingpin longboardBaseplate Angle:40° or 50°Hanger Width:155mm or 180mmConstruction:Forged hanger and baseplate
Typical price range$59.99

At a glance

Brand
Not synced yet
Model
Not synced yet
MPN
Not synced yet
Category
Skateboard Trucks & Hardware
Status
Offers available
Data updated
Nov 16, 2026

Current offers

Highlights

  • Gen 6 trucks use a forged hanger and baseplate for higher strength-to-weight than cast trucks, reducing bending under hard carving.
  • Available in 40° and 50° baseplate angles: 40° is more stable for downhill and freeride, 50° is quicker for commuting and cruising.
  • Hanger widths include 155mm and 180mm; 155mm suits decks around 8.5–9.5 inches wide, 180mm suits 9.5–10.5 inches.
  • Gen 6 uses a new bushing seat and kingpin design that reduces slop and improves return-to-center compared to Gen 5.

Best use cases

  • Downhill and freeride: choose 40° baseplate and 155mm hanger for stability and quick rail-to-rail transitions on narrower decks.
  • Commuting and carving: choose 50° baseplate and 180mm hanger for responsive turning and a surfy feel on wider decks.
  • Street and tech sliding: skip Gen 6 and use traditional kingpin trucks; reverse kingpin trucks sit higher and are less stable for flip tricks.
  • Wrong fit: do not put 155mm hangers on a 10-inch deck or 180mm hangers on a 8.5-inch deck—axle width must match deck width within 0.5 inches.

Buying tips

  • Match hanger width to deck width: measure deck at the trucks; 155mm fits 8.5–9.5 in, 180mm fits 9.5–10.5 in; axle should not extend more than 0.25 in past deck edge.
  • Choose baseplate angle by discipline: 40° for speeds above 20 mph or freeride; 50° for carving and commuting below 20 mph.
  • Bushing durometer: use 90a for riders 120–170 lbs, 93a for 170–210 lbs, 96a for 210+ lbs; softer bushings turn more but reduce stability.
  • Gen 6 trucks use a 2.5-inch kingpin and standard 8mm axles; ensure your deck has a 2.125-inch truck mounting hole pattern (new school).

Specs

Truck TypeReverse kingpin longboard
Baseplate Angle40° or 50°
Hanger Width155mm or 180mm
ConstructionForged hanger and baseplate

Alternatives to compare

Related searches

What to check before buying

  • Measure deck width at the front truck mounting holes; confirm 155mm or 180mm hanger matches within 0.5 inches.
  • Check deck truck mounting hole pattern: new school (2.125 in) is required; old school (2.5 in) will not fit without redrilling.
  • Verify wheel clearance: Gen 6 trucks add about 2.5 inches of axle height; ensure your deck and wheels do not cause wheel bite with your chosen bushing durometer.
  • Confirm your weight and riding style against bushing durometer chart; stock 90a bushings suit riders up to about 170 lbs for general cruising.

FAQ

All Skateboard Trucks & Hardware buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 16, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.