Photos from current listings. Actual item, color, and included accessories may vary.
Bone Red Bearing Buying Guide
Bones Reds are the benchmark entry-level skateboard bearing, using non-contact rubber shields and factory light oil for speed with minimal maintenance. The primary trade-off is price versus durability: standard Reds use steel races and balls that rust under moisture, while Swiss and Ceramic tiers upgrade materials for longer life. The clear decision rule is to buy standard Reds for dry street/park use and step up to Swiss or Ceramic only if you skate wet conditions or demand maximum roll speed and corrosion resistance.
At a glance
- Category
- Skateboard Wheels & Bearings
- Data updated
- Nov 16, 2026
Current offers
Highlights
- Bones Reds use non-contact rubber shields (removable) and are factory-lubricated with light speed oil, not grease—this yields low rolling resistance but requires frequent cleaning in dusty environments.
- Standard Reds have steel balls and races with a durometer-optimized nylon ball retainer; they are NOT rust-proof, so wet skating demands Swiss or Ceramic upgrades.
- Bones Swiss bearings use higher-grade steel and tighter tolerances for faster roll and longer life, but they still rust if water penetrates the non-contact shields.
- Bones Ceramic Super Reds substitute ceramic balls (silicon nitride) with steel races—ceramic balls resist rust and deformation, but the steel races remain susceptible to corrosion.
Best use cases
- Best fit: street and park skaters in dry climates who want proven speed and easy cleaning—choose standard Bones Reds (8-pack) and budget for periodic replacement.
- Wrong fit: dedicated wet-weather or slush skaters—skip standard Reds because steel races will rust; choose full ceramic bearings with ceramic races or accept frequent replacement.
- Best fit: competitive downhill or longboard distance skaters needing maximum roll speed and heat resistance—upgrade to Bones Ceramic Super Reds (ceramic balls) or Swiss Ceramics.
- Best fit: cruiser or rough-surface riders prioritizing durability over ultimate speed—Bones Swiss (higher-grade steel) outlast Reds under impact loads, but still avoid water.
Buying tips
- Buy an 8-pack for a standard skateboard (4 wheels × 2 bearings). A 16-pack covers two complete setups or spares; singles are not cost-effective for a full swap.
- Match bearing size: skateboard wheels universally use 608 bearings (8mm inner diameter, 22mm outer, 7mm width). Confirm your axle is 8mm standard—most trucks are.
- Upgrade path: standard Reds → Swiss (better steel, tighter tolerances) → Ceramic Super Reds (ceramic balls) → Swiss Ceramics (ceramic balls + races). Each step increases corrosion resistance and roll speed.
- Shield choice: non-contact rubber shields (Reds) spin faster but let in dirt; contact shields (some Swiss models) seal better but add friction—pick based on cleanliness of your skating surfaces.
Specs
| Bearing Size | 608 (8x22x7mm) |
|---|---|
| Shield Type | Non-contact rubber, removable |
| Ball Material | Steel / Ceramic (model-dependent) |
| Pack Size | 8-pack (standard skateboard) |
Related searches
What to check before buying
- Confirm wheel bearing seat accepts standard 608 bearings (22mm outer diameter)—virtually all skateboard wheels do, but recheck vintage or specialty wheels.
- Inspect axle diameter: 8mm is standard for skateboard trucks; 10mm axles require different bearings (rare on street boards).
- Assess climate: if you routinely skate wet or humid conditions, budget for Swiss or Ceramic tiers or plan to clean/relube Reds frequently.
- Check existing bearing condition: worn or seized bearings can damage wheel cores—replace all 8 at once for even wear.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 16, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.

