Trail Gear Advisor

All Terrain Skateboard Wheel Buying Guide

All-terrain skateboard wheels are the contact patch that lets a board roll over rough asphalt, packed dirt, and cracked pavement without losing speed or control. The core trade-off is urethane hardness and diameter against terrain severity: harder, smaller wheels roll fast on smooth concrete but transmit vibration, while softer, larger wheels absorb impact at the cost of acceleration and slide predictability. The durable rule is simple: match durometer to surface roughness and diameter to debris height, and never buy a wheel whose core or urethane grade is unspecified.

Durometer Range:78A–85A all-terrain / 90A+ parkWheel Diameter:65–80mm all-terrain / 52–60mm streetCore Material:Reinforced nylon or fiberglass vs solid urethaneBearing Standard:608 (22mm OD / 8mm ID)

At a glance

Price range
Price range not synced yet
Category
Skateboard Wheels & Bearings
Data updated
Nov 16, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Durometer is the primary terrain filter: 78A–85A soft urethane grips rough pavement and dampens vibration; 90A–101A hard wheels slide predictably on smooth parks but chatter on gravel and cracks.
  • Diameter drives rollover ability: 65–75mm wheels clear pebbles, expansion joints, and dirt ruts; 55–60mm wheels are park/street oriented and hang on debris.
  • Core construction separates durable all-terrain wheels from compromises: reinforced nylon or fiberglass cores resist spoke shear and hub ovalization under lateral loads; solid urethane cores flex and flat-spot faster.
  • Contact patch and edge radius matter: wider contact patches (35–45mm) float over loose dirt and gravel, while rounded edges reduce bite on rough transitions; square edges track straighter on pavement.

Best use cases

  • Best fit: rough asphalt, chip-seal roads, and cracked sidewalks — choose 70–75mm, 78A–83A wheels with a reinforced core and 40–45mm contact patch for roll speed and vibration damping; skip 54–60mm park wheels.
  • Best fit: packed dirt, gravel paths, and light off-road — choose 72–80mm, 78A–80A wheels with a wide contact patch and rounded edges for float; skip hard 99A+ wheels that sink and stall.
  • Best fit: mixed commuting with curb drops and occasional park — choose 65–70mm, 85A–90A wheels with a medium contact patch; skip pure 78A downhill wheels if you need slide control on concrete.
  • Wrong fit: technical street skating and ledge tricks — all-terrain diameters (70mm+) wheel-bite on turns and slow flip setup; use 52–56mm, 99A–101A street wheels instead.

Buying tips

  • Match durometer to surface: 78A–85A for asphalt, dirt, and gravel; 85A–90A for mixed pavement and park; 90A–101A only for smooth concrete parks. Softer than 78A wears fast on abrasive pavement.
  • Size by debris and terrain: 65–70mm for cracked urban pavement, 70–75mm for rough chip-seal and dirt, 75–80mm for gravel and off-road float. Anything under 60mm is a park/street wheel, not all-terrain.
  • Check core and urethane grade: reinforced nylon or fiberglass cores resist hub shear at 70mm+ diameters; look for poured urethane (not injected) for rebound and flat-spot resistance.
  • Verify truck compatibility: wheels over 70mm require riser pads (1/8–1/2 in) to prevent wheel bite; confirm axle width and bearing seat (standard 608) before buying.

Specs

Durometer Range78A–85A all-terrain / 90A+ park
Wheel Diameter65–80mm all-terrain / 52–60mm street
Core MaterialReinforced nylon or fiberglass vs solid urethane
Bearing Standard608 (22mm OD / 8mm ID)

Related searches

What to check before buying

  • Measure your deck and truck width: all-terrain wheels 70mm+ need a deck wide enough (8.0–8.5in) and trucks that don't extend past the deck edge, or you'll get wheel bite on turns.
  • Check your current riser setup: adding 70mm+ wheels to a standard-height truck requires 1/8–1/2 in riser pads and possibly longer hardware; measure available clearance before purchase.
  • Confirm bearing standard: all-terrain wheels use standard 608 bearings (22mm OD, 8mm ID); verify your existing bearings or buy a set with the wheels.
  • Assess surface abrasiveness and climate: soft 78A urethane wears quickly on coarse chip-seal; hot climates soften urethane further, so step up 2–3A in durometer for longevity.

FAQ

All Skateboard Wheels & Bearings buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 16, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.