Trail Gear Advisor

Bone Skateboard Bearing Buying Guide

Bone Skateboard Bearings refers to the Bones Bearings line and its clones, where the core trade-off is ABEC-rated precision (speed) versus built-in serviceability and durability (built-in spacers, removable shields, grease vs. oil). The decision rule is simple: buy certified Bones Swiss or Reds with removable rubber shields for street/park use, and skip unbranded 'Bones-style' bearings that lack serviceable shields or clear ABEC/grade markings.

Bearing Grade:ABEC-1 to ABEC-7 (ABEC-9 overkill)Shield Type:Rubber (Reds) vs removable metal/rubber (Swiss)Ball Material:Steel vs ceramic (Si3N4)Dimensions:8x22x7mm standard; 10mm seat for built-in

At a glance

Price range
Price range not synced yet
Category
Skateboard Wheels & Bearings
Data updated
Nov 16, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Bones Reds are single, non-removable rubber-shielded bearings with pre-lubricated grease; Bones Swiss use removable shields and lighter oil for higher top speed but require more maintenance.
  • ABEC rating (ABEC-1, 3, 5, 7, 9) describes dimensional tolerance, not load capacity or dirt resistance; for skateboarding, ABEC-5 to ABEC-7 is the practical sweet spot, while ABEC-9 offers negligible real-world gain and tighter tolerances that wear faster in gritty conditions.
  • Bones Swiss Ceramics (Si3N4 ceramic balls) resist rust and handle heat better than steel but are brittle under impact; steel bearings (Bones Reds, Super Reds) are more forgiving for street impacts and cost far less.
  • Built-in spacers and speed washers (Bones Swiss Six Ball, Bones Super Swiss 6) reduce friction and simplify wheel installation, but only work with wheels that have the correct bearing seat depth; standard 8mm axle bearings without built-in spacers need separate spacers and washers.

Best use cases

  • Best fit: Street and park skaters who want low-maintenance durability — choose Bones Reds (grease-packed, shielded) and skip Swiss Ceramics unless you skate in wet or dusty environments where rust resistance matters more than impact toughness.
  • Best fit: Bowl, vert, and downhill riders chasing top speed with frequent cleaning — choose Bones Swiss (removable shields, oil lube) and pair with a bearing cleaning kit; skip Reds if you want serviceable shields without prying.
  • Wrong fit: Cruisers and longboarders using wet or salty roads — standard steel Bones bearings will seize; pick ceramic or stainless-steel bearings instead, and skip any bearing labeled 'Bones' without a grade or shield spec.
  • Wrong fit: Budget completes or kids' first boards — unbranded 'Bones-style' bearings with non-removable metal shields are disposable; skip them and buy genuine Bones Reds, which cost marginally more but last multiple seasons.

Buying tips

  • Match bearing width to wheel core: standard skateboard bearings are 8mm ID x 22mm OD x 7mm wide; built-in-spacer bearings (e.g., Bones Swiss Six Ball) require wheels with a 10mm-wide bearing seat or they will bind.
  • Choose shield type by maintenance habit: rubber-shielded (Reds) keeps grease in and dirt out with no service; removable metal or rubber shields (Swiss) demand periodic cleaning and re-oiling but deliver lower rolling resistance.
  • Verify grade and country of origin: genuine Bones bearings are made in Switzerland (Swiss) or China (Reds) and marked with 'Bones' and the model; generic 'ABEC-9 Bones' bearings with no origin stamp are counterfeit or white-label.
  • Buy a full set of 8 bearings plus spare shields and speed washers; bearings wear as a set, and mixing old and new bearings in one board causes uneven roll and premature flat spots.

Specs

Bearing GradeABEC-1 to ABEC-7 (ABEC-9 overkill)
Shield TypeRubber (Reds) vs removable metal/rubber (Swiss)
Ball MaterialSteel vs ceramic (Si3N4)
Dimensions8x22x7mm standard; 10mm seat for built-in

Related searches

What to check before buying

  • Measure your wheel's bearing seat: standard 7mm-wide seats take standard 8x22x7mm bearings; 10mm-wide seats accept built-in-spacer bearings only.
  • Confirm axle diameter: 8mm is standard skateboard; 10mm axles require 10mm-ID bearings (rare on street boards, common on some longboards).
  • Check your climate: humid or coastal environments favor ceramic or stainless bearings; dry street skating favors steel with grease.
  • Have a bearing press or socket on hand: removable-shield bearings need periodic cleaning, and pressing bearings in crooked ruins the wheel core.

FAQ

All Skateboard Wheels & Bearings buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 16, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.