Trail Gear Advisor

Photos from current listings. Actual item, color, and included accessories may vary.

Longboard Wheel And Bearing Buying Guide

Longboard wheels and bearings are the contact-patch and rolling system that define grip, slide predictability, roll speed, and ride comfort. The core trade-off is urethane hardness and wheel geometry versus surface conditions: softer, wider wheels absorb rough pavement and grip, while harder, narrower, sharply-lipped wheels break traction predictably for sliding. Buyers should choose wheels by durometer and contact patch for their discipline, then match bearings by ABEC tolerance and built-in spacer/race design rather than marketing names.

Durometer Range:75a–86a+ (soft to hard)Wheel Diameter:60–80mm longboard rangeBearing Standard:8mm axle / 22mm ODBearing Shield:Rubber sealed vs metal shielded
Typical price range$40.00 – $60.00

At a glance

Category
Skateboard Wheels & Bearings
Data updated
Nov 16, 2026

Current offers

Highlights

  • Durometer scales run roughly 75a–80a for downhill grip and rough-road comfort, 81a–85a for freeride slide balance, and 86a+ for technical slide and park use.
  • Wheel diameter 65–75mm with 50–70mm contact patch suits most longboard disciplines; larger diameters roll faster but increase wheelbite risk on narrow trucks.
  • Bearings marked ABEC 7/9 are precision-tolerance only; integrated spacer and race designs (e.g., built-in half-spacers) reduce side-load binding under longboard trucks.
  • Rain grooves and square lips improve wet-pavement water evacuation and grip predictability; rounded lips release slides more smoothly for freeride.

Best use cases

  • Downhill and fast freeride: pick 70–76mm wheels at 75a–80a with square or grooved lips and ABEC 7+ steel bearings for grip and heat resistance; skip soft cruiser wheels that chunk under speed.
  • Commuting and rough pavement: choose 70–80mm at 78a–80a with wide contact patch and sealed bearings for vibration damping; skip hard slide wheels that transmit road chatter.
  • Freestyle and dancing: select 60–65mm at 81a–84a with rounded lips for predictable slides and light weight; skip large downhill wheels that cause wheelbite on narrow trucks.

Buying tips

  • Match durometer to surface: 75a–80a for cracked asphalt and grip, 81a–85a for slide initiation, 86a+ only for smooth parks and technical sliding.
  • Keep wheel diameter within 5mm of stock to avoid wheelbite; going from 65mm to 75mm on the same truck adds 10mm total height and requires riser pads or truck adjustment.
  • Choose bearings with built-in spacers and speed rings if your wheels use a standard 8mm axle; loose bearings without spacers bind and flat-spot under longboard side loads.
  • For wet or gritty conditions, pick sealed bearings (rubber shields) over metal-shielded race bearings; rubber seals block water and grit at a small roll-speed cost.

Specs

Durometer Range75a–86a+ (soft to hard)
Wheel Diameter60–80mm longboard range
Bearing Standard8mm axle / 22mm OD
Bearing ShieldRubber sealed vs metal shielded

Related searches

What to check before buying

  • Measure your deck wheel wells and truck width: confirm at least 5mm clearance at full lean for the wheel diameter you plan to run.
  • Check axle diameter (8mm standard on most longboards, 10mm on some downhill trucks) and bearing bore size before ordering.
  • Confirm truck kingpin and baseplate height allow the wheel diameter; add riser pads if increasing wheel size by more than 5mm.
  • Verify the wheel's bearing seat accepts standard 22mm OD bearings and that your chosen bearings include spacers if the wheels require them.

FAQ

All Skateboard Wheels & Bearings buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 16, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.