Trail Gear Advisor

Photos from current listings. Actual item, color, and included accessories may vary.

Longboard Truck And Wheel Buying Guide

Longboard trucks and wheels are the steering and grip interface of a board, where axle width, bushing durometer, and wheel urethane formula determine stability, turn feel, and slide predictability. The core trade-off is precision-machined geometry and high-rebound urethane versus cast tolerances and generic rubber — the former holds alignment and speed, the latter wears and wobbles. Decide by discipline: freeride/downhill demands tight-tolerance trucks and stone-ground wheels; cruising/carving favors wider axles and softer, larger contact patches.

Truck Axle Width:150–160 mm or 180 mmBushing Durometer:85a–95a (weight-dependent)Wheel Urethane:78a–86a (cruise to slide)Wheel Contact Patch:30–35 mm grip/slide balance
Typical price range$59.99

At a glance

Category
Skateboard Trucks & Hardware
Data updated
Nov 16, 2026

Current offers

Highlights

  • Truck width is measured axle-end to axle-end: 150–160 mm suits 9–9.5-inch decks, 180 mm suits 9.5–10.5-inch decks for stable freeride.
  • Bushing durometer 90a–93a gives responsive carve on flat ground; 85a–88a adds lean for downhill, while 95a+ resists slop at speed.
  • Wheel urethane 78a–80a grips and absorbs rough pavement; 83a–86a enables predictable slides and even wear on freeride setups.
  • Precision trucks use tight-tolerance axles and kingpin geometry for zero slop; cast trucks flex slightly and need more frequent bushing checks.

Best use cases

  • Freeride/downhill: pick 180 mm precision or tight-tolerance cast trucks with 83a–86a stone-ground wheels; skip 150 mm axles and softer than 80a urethane.
  • Commuting/carving: choose 150–160 mm trucks with 90a bushings and 78a–80a wheels in 65–70 mm diameter for roll speed and curb clearance.
  • Pumping/slalom: use narrower 130–150 mm trucks with 85a–88a bushings and 70–75 mm wheels; avoid 180 mm axles that slow turn initiation.

Buying tips

  • Match truck axle width to deck width at the widest point: axle should equal or be 5–10 mm narrower than deck for leverage without wheel bite.
  • For 70 mm wheels, add at least 2 mm riser pad or choose trucks with 55–60 mm axle height to prevent bite on hard turns.
  • Bushing shape matters: barrel/cone combo gives linear lean; double barrel adds stability for fast freeride; double cone is too loose for downhill.
  • Wheel contact patch 30–35 mm balances grip and slide; 40 mm+ patches grip hard but slow slides and wear faster on rough asphalt.

Specs

Truck Axle Width150–160 mm or 180 mm
Bushing Durometer85a–95a (weight-dependent)
Wheel Urethane78a–86a (cruise to slide)
Wheel Contact Patch30–35 mm grip/slide balance

Related searches

What to check before buying

  • Measure deck width at front and rear truck mounting holes; confirm axle width is within 10 mm of that number.
  • Check wheel well cutouts: wheel diameter plus 5 mm clearance must fit inside cutout at full lean.
  • Verify truck mounting hole pattern matches deck (new-school 2.125-inch or old-school 2.625-inch).
  • Confirm bushing durometer suits your weight: under 150 lb use 85a–88a, 150–200 lb use 90a–93a, over 200 lb use 95a+.

FAQ

All Skateboard Trucks & Hardware buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 16, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.